Tiempos abiertos prolongados para la reparacin con morteros. DO NOT ADD WATER. Tel. Corrosion Protection and/or Bonding Primer: Contains EpoCem technology - improved bonding agent, Compatible with most Sika repair mortars, Certified for application under dynamic load conditions, Good resistance to water and chloride penetration, Can be brushed on or applied using spray gun, Suitable for control of anodic areas (Principle 11, method 11.1 EN 1504-9). Rsistance leve au cisaillement. Condition Sika Armatec-10 ZR to 45 - 95 F (7 - 35 C) prior to use. 8. Maharashtra 400706 Vynikajc pilnavost na oceli a betonu. Clean all tools and application equipment with water immediately after use. Compatible with most Sika MonoTop repair mortars. Nz*WK~a LIendstream elementary particle 6 letters. Bonding Primer and Reinforcement Corrosion Protection, Quality Environment Health and Safety Policy, Pre-treatments, Accessories & Intermediates, Economic, Environmental and Social Dimensions, Bonding Primer / Reinforcement Corrosion Protection. ;|9_ ?EE[g@2w2:EllLC7jbfV.tY+,gB!C;35SRCm8/rOH[^uJPXi$!R_%:Zm|Tf~nR"4 SikaTop Armatec-110 EpoCem is a cementitious, epoxy resin compensated 3-component coating material with corrosion inhibitor, used as bonding primer and reinforcement corrosion protection. ), Erbil / Baghdad / Basra, Tel: +96 477 303 74451, info@iq.sika.com, irq.sika.com Subject: : +65 6861 0632 z6N!`0Y/O\h>d%Cfh0N:z-ZV_2Ke -hU:;9cAt+No~S>Z[C! Excellent adhesion to concrete and steel. APPLICATION The application of a suitable bonding agent, such as Before pouring, leave the mixed grout to stand for ap-Sikadur-32 LP or SikaTop Armatec-110 EpoCem, proximately 5 minutes, to allow entrapped air to es-will improve adhesion on large areas or where particu- cape. 61, DM No. Leave to stand for 510 minutes until mixed coating material exhibits a brush-able, weakly dripping consistency.DO NOT ADD WATER. SikaTop Armatec-110 EpoCem is a cementitious, epoxy resin compensated three-component coating material with corrosion inhibitor, used as bonding primer and reinforcement corrosion protection. Excellent adhesion to concrete and steel. <> NOA No. SikaTop Armatec-110 EpoCem Author: Sika Iraq (Sika Trading L.L.C. SikaTop Armatec-110 EpoCem can be mixed with a low speed (< 250 rpm) electric drill mixer. Verlngerte berarbeitungszeiten fr Reparaturmrtel. To achieve good bond, SikaTop Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). For the best results, :g4p93NPsCH 5 w]#d/KQwIc=_m}=h. Freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain until application of the repair mortar. You are here: us silica holdings inc annual report / community college woodworking classes / farm house for rent in bangalore / bonding agent for plaster to concrete E-mail: [emailprotected]. Use a 3/8" (10 mm) nap roller or a round brush. E-mail: [emailprotected], Bonding Primer and Reinforcement Corrosion Protection, Sustainability / Certifications / Approvals, Bonding Primer / Reinforcement Corrosion Protection, Sika MonoTop, SikaRep, Sikagard series. SIKA ARMATEC 110. endstream Apply subsequent repair mortars wet on wet freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain until application of the repair mortar. While still mixing components A and B slowly add powder component C. Mix the three components together for a minimum 3 minutes, minimising addition of air. Extended open times for repair mortars. Leave to stand for 5 to10 minutes until mixed coating material exhibits a brush-able, weakly dripping consistency. Extended open times for repair mortars. Kn:&} \@1[gaI5MN0-ybeaANn6:s%";7Bjk%e9U[k`pj +WPVx-=Yb&MkJ*+'K=tuP/K}p/1WU1>24>Fynr Apply subsequent repair mortars wet on wet Freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain until application of the repair mortar. This website uses cookies to provide you with a greater user experience. Part C must be protected from humidity. Bhd., Lot 689, Nilai Industrial Estate, 71800 Nilai, Negeri Sembilan D.K., Malaysia, Phone: +606-7991762, Fax: +606-7991980, e . Clean all tools and application equipment with water immediately after use. endobj _4d]O=G"DTE+yendstream Apply subsequent repair mortars wet on wet freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain until application of the repair mortar. The proprietary rights of third parties must SikaTop Armatec-110 EpoCem Author: Sika Kimia Sdn. Plot No D 101/2,MIDC Industrial Area Apply subsequent repair mortars wet on wet Freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain until application of the repair mortar. Item #: THOTCCP.5. SikaTop Armatec-110 EpoCem Author: Sika South Africa (Pty) Ltd, 9 Hocking Place,, Westmead, 3608, South Africa, Phone +27 31 792 6500, www.sika.co.za Subject: sign in; all products. 68 0 obj 59 0 obj :6DuSVD~?"cj^t})pr}8LFp tions relating to the application and end-use of Sika products, are given in good faith based on Sika's cur-rent knowledge and experience of the products when . Certified for application under dynamic load conditions. By using our site, you accept our use of cookies. Sika re-serves the right to change the properties of its products. As a bonding primer: Apply using medium hard brush or spray gun to prepared substrate. Avec la technologie EpoCem - Adhrence amliore. Apply subsequent repair mortars wet on wet. Contains EpoCem technology - improved bonding agent. Response: P302 + P352 IF ON SKIN: Wash with plenty of water. Hardened material can only be mechanically removed. While still mixing components A and B slowly add powder component C. Mix the three components together for a minimum 3 minutes, minimising addition of air. TEL FR : +33 362276125 TEL BE : +32 69549900 Contains EpoCem technology - improved bonding agent. Lista dos nossos produtos mais vendidos. x]@8w-7&,4E-T{n4Z@jI|na:chqhW=+ E(M5K1IJ'LqhjPML!VAmU#rK'\)U^z_+%:5*qb21G! Store at temperatures between +5C and +40C. endobj 3-komponentiger, epoxidharzvergteter PCC-Korrosionsschutz und Haftbrcke, die den Anforderungen der EN 1504-7 entspricht. tel fr : +33 362276125 tel be : +32 69549900 Apply subsequent repair mortars wet on wet Freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain until application of the repair mortar. Certifi pour une application dans des conditions de charge dynamique. Store properly in undamaged original sealed packaging, in dry cool conditions between +5 C and +25 C. xT]@}W7[dqnL1%ahaU{JtpS932>=HDa(ur. Leave to stand for 510 minutes until mixed coating material exhibits a brushable, weakly dripping consistency. . 78 0 obj Facile mlanger. SikaTop Armatec-110 EpoCem meets the requirement of EN 1504-7. APPLICATION INFORMATION Fresh Mortar Density A+B+C ~125 lb/ft3 (~2.0 kg/l) Coverage Bonding agent 80 ft2/gal (7.4 m2/l) endobj Dry Spray Process: Protect the fresh mortar from rain while the material has not yet set. To achieve good bond, SikaTop Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 millimeter). Contiene la tecnologa EpoCem - puente de adherencia superior. Excellent adhesion to concrete and steel. <> Contains corrosion inhibitor. Apply subsequent repair mortars wet on wet Freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain un-til application of the repair mortar. 2 layer thickness (~2 mm thick)As a bonding primer, substrate:> 1.5 to 2.0 kg per m2 /mm dependent on substrate conditions. LPM, Laboratory for Preparation and Methodology, Beinwil am See, Switzerland Ibac Aachen A 3119/3. System Structure SikaTop Armatec-110 EpoCem is part of the Sika repair system com-plying with the relevant part of European Standard EN 1504 and compris- . SikaTop Armatec-110 EpoCem is a cementitious, epoxy resin modified 3-component coating material with corrosion inhibitor, used as bonding primer and reinforcement corrosion protection. ,fM$-p!)Q:N!snB8V4F8Ey$xo"Z@( W[yTJ0(my.yUxdU1*>sU23E\~QbK!yv^ . SikaTop Armatec-110 EpoCem Author: Sika Canada Inc., Head Office, 601, avenue Delmar, Pointe-Claire, Quebec, H9R 4A9, 1-800-933-SIKA, www.sika.ca Subject: Product Data Sheet SikaTop Armatec-110 EpoCem meets the requirement of EN 1504-7. tel fr : +33 362276125 tel be : +32 69549900 As a bonding primer:Apply using medium hard brush or spray gun to prepared substrate. tions relating to the application and end-use of Sika products, are given in good faith based on Sika's cur-rent knowledge and experience of the products when . SikaTop Armatec-110 EpoCem. db[B] k/]-Zi"=q&n4q~`6q%k0X{@/`yiV@ak_sj]H/ddj^~:WbaI,P{=W@|$.Pmwz#z Extended open times for repair mortars. . !SyXFlLfjk>W|[7"RMX$@3iPW\\>^6b\|hCue>iJP!{0Y_rzeLpA5JGB.BAaLN-"xStcc5[H 8Lw}JDc SikaTop Armatec-110 EpoCem is a cementitious, epoxy resin compensated 3-component coating material with corrosion inhibitor, used as bonding primer and reinforcement corrosion protection. Pour liquid components A and B into a suitable mixing vessel and mix for 30 seconds. Compare NEWBORN 373-XSP . SikaTop Armatec-110 EpoCem meets the requirement of EN 1504-7. : +351 223 776 900, prt.sika.com Subject: Ficha de Dados do Produto Keywords: SikaTop Armatec-110 EpoCem 020302020050000001 AGENTE DE ADERNCIA E REVESTIMENTO ANTICORROSIVO PARA ARMADURAS Obsahuje inhibitory koroze. Pour liquid components A and B into a suitable mixing vessel and mix for 30 seconds. Refer to separate sheets for further information. Application. tions relating to the application and end-use of Sika products, are given in good faith based on Sika's cur-rent knowledge and experience of the products when . 9 0 obj Mfr #: 324322 From: $244.11 Add to Cart. Fax : +91 22 62704039, Bonding Primer and Reinforcement Corrosion Protection. Certified for application under dynamic load conditions. 60 0 obj 67 0 obj Apply subsequent repair mortars wet on dry (so not to wipe off the protection layer). Raya Cibinong-Bekasi Km.20, Limusnunggal-Cileungsi, Bogor 16820-Indonesia, Tel. The Piero T 101 101 110 110 110 N Not To Scale 10 10 Lattc (adams) Pico Pershing Square Civic Center/ Grand Park 7th/ Metro To Koreatown, Hollywood, The Valley To Highland Park, Pasadena 110 110 10 210 10 5 405 405 101 101 Hollywood "the Valley . Sika Armatec-110 EpoCem March 2020, Version 01.02 020302020050000003 PRODUCT DATA SHEET Sika Armatec-110 EpoCem BONDING PRIMER AND REINFORCEMENT CORROSION PROTECTION . Sika repair mortars and non-fast setting concrete can be applied on SikaTop Armatec-110 EpoCem within a maximum time of: Reinforcement corrosion protection coating. Bonne rsistance la pntration de l'eau et de chlorures. Item #: SIK110.165. Application: Tapered or flat boards suitable for use in insulated roofing system constructions utilizing built-up roof, modified bitumen, or single-ply membranes and metal . SikaTop Armatec-110 EpoCem . Trials are recommended to confirm suitabil- for the intended application and purpose. Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). SikaTop-Armatec 110 EpoCem is anti-corrosion coating for reinforcement steel: Sika Chemical Anchoring Adhesive Volume Calculator App, Sustainability / Certifications / Approvals, Contains EpoCem technology - improved bonding agent, Compatible with most Sika MonoTop repair mortars, Provides an excellent bonding coat for subsequent application of repair mortars cement and epoxy based, Certified for application under dynamic load conditions, Good resistance to water and chloride penetration, Can be brushed on or applied using spray gun, For repairs to reinforced concrete where there is corrosion of the underlying reinforcement steel, For the preventive protection of reinforcement steel in thin reinforced concrete sections, For repairs to concrete using SikaTop patching and repair mortars. Suitable as a bonding primer on concrete and mortar, Testing according to BS 1881, Part 207 : 1992, Cl. w'>\$V!=jibZvK,yJewG(~ra>+wgt'bXe1?&^ Application Documents Usage SikaTop-Armatec 110 EpoCem is anti-corrosion coating for reinforcement steel: For repairs to reinforced concrete where there is corrosion of the underlying reinforcement steel For the preventive protection of reinforcement steel in thin reinforced concrete sections CURING TREATMENT stream Sika . SikaTop Armatec-110 EpoCem meets the requirement of EN 1504-7. }V/]U0R!][_Y>.Kv( 'G I, >[?T"*MC*RQAt4{Z{?Xendstream SikaTop Armatec-110 EpoCem (A) SDS Number Version 1.0 : 000000022459 Revision Date 08.11.2018 2 / 8 P272 Contaminated work clothing should not be allowed out of the workplace. Suitable for use in hot and tropical climatic conditions. x[M# >AUYY&ypg5\?DJT*w:0h(#EE,+kbqWzE ^ c.?i?.*\?^UG{MU SikaTop Armatec-110 EpoCem meets the requirement of EN 1504-7. Obsahuje technologii EpoCem - zvyuje pdrnost. Corrosion Protection and/or Bonding Primer: Contains EpoCem technology - improved bonding agent, Compatible with most Sika MonoTop repair mortars, Certified for application under dynamic load conditions, Good resistance to water and chloride penetration, Can be brushed on or applied using spray gun, Suitable for control of anodic areas (Principle 11, method 11.1 EN 1504-9). Clean all tools and application equipment with water immediately after use. Sika Armatec-110 EpoCem March 2020, Version 01.02 020302020050000003 PRODUCT DATA SHEET Sika Armatec-110 EpoCem BONDING PRIMER AND REINFORCEMENT CORROSION PROTECTION . Apply subsequent repair mortars wet on wet Freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain until application of the repair mortar. SikaTop Armatec-110 EpoCem Author: SIKA NORTHERN GULF, Bahrain / Qatar / Kuwait, Tel: +973 177 38188, sika.gulf@bh.sika.com, gcc.sika.com Subject: Product Data Sheet 410 %PDF-1.4 for the intended application and purpose. xMN0s tions relating to the application and end-use of Sika products, are given in good faith based on Sika's cur-rent knowledge and experience of the products when SikaTop Armatec-110 EpoCem is part of the Sika repair system complying with the relevant part of European Standard EN 1504 and comprising of: Maximum waiting time before application of repair mortar Sika repair mortars and non-fast setting concrete can be applied on SikaTop Armatec-110 EpoCem within a maximum time of: As reinforcement corrosion protection coating:~ 2 kg per m2 and application layer (~1 mm thick)In total minimum 2 layer thickness (~2 mm thick)As a bonding primer, substrate:> 1.5 to 2.0 kg per m2 /mm dependent on substrate conditions, SikaTop Armatec-110 EpoCem can be mixed with a low speed (< 250 rpm) electric drill mixer.Shake components A and B thoroughly before opening. endobj that SikaTop Armatec-110 EpoCem be used as a bonding agent. Suitable in concrete repair as corrosion protection for reinforcement. SikaTop Armatec-110 EpoCem meets the requirement of EN 1504-7. Suitable as a bonding primer on concrete and mortar. Application under dynamic loading: SikaTop Armatec-110 EpoCem has been tested with the following Sika repair mortars and is certified for dynamic loading applications. P280 Wear protective gloves/ eye protection/ face protection. Jul 20th, 2022 SikaTop Armatec -110 EpoCem - Bel.sika.com SikaTop Armatec-110 EpoCem 1 . endobj System Structure SikaTop Armatec-110 EpoCem is part of the Sika repair system com-plying with the relevant part of European Standard EN 1504 and compris- . APPLICATION. APPLICATION INFORMATION Fresh Mortar Density A+B+C ~125 lb/ft3 (~2.0 kg/l) Coverage Bonding agent 80 ft2/gal (7.4 m2/l) Hardened material can only be mechanically removed. contact prijopgave prijopgave . : 01 49 92 80 00, Fax: 01 49 92 85 88, www.sika.fr Subject: Notice Produit Keywords: SikaTop Armatec-110 EpoCem 020302020050000001 Barbotine d accrochage pour mortier / protection des armatures. Fax: +65 6862 3915 stream SikaTop Armatec-110 EpoCem is a cementitious epoxy resin compensated 3-component coating material with corrosion inhibitor, used as bonding primer and reinforcement corrosion protection. Contains EpoCem technology - improved bonding agent Extended open times for repair mortars tions relating to the application and end-use of Sika products, are given in good faith based on Sika's cur-rent knowledge and experience of the products when !orFOL`2fW*. The above consumptions are approximate and dependent on method of application and substrate conditions. : +971 4 439 8200 Store properly in unopened original packing. Extended open times for repair mortars. Protect the fresh mortar from rain while the material has not yet set. SikaTop Armatec-110 EpoCem . To achieve good bond, SikaTop Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). Pour liquid components A and B into a suitable mixing vessel and mix for 30 seconds. To achieve good bond, SikaTop Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 millimeter). 768 Certified for application under dynamic load conditions. Dry Spray Process: Protect the fresh mortar from rain while the material has not yet set. Compatible with most Sika MonoTop repair mortars. To achieve good bond, SikaTop Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). SikaTop Armatec-110 EpoCem cumple los requerimientos de la norma EN 1504-7. Certified for application under dynamic load conditions. 20 kg: A (1.14 kg) + B (2.86 kg) + C (16 kg), Portland cement, epoxy resin, selected aggregates and additives. Apply 2nd layer when the first coat is hard to the fingernail (approximately 2 to 3 hours at +20 C). Mit EpoCem Technologie - verbesserte Haftung. SikaTop Armatec-110 EpoCem meets the requirement of EN 1504-7. tions relating to the application and end-use of Sika products, are given in good faith based on Sika's cur-rent knowledge and experience of the products when . Dubai Industrial City, Saih Shuaib 4 Plot No. Apply subsequent repair mortars wet on dry (so not to wipe off the protection layer). Contains EpoCem technology - improved bonding agent. Sikadur-32 LP or SikaTop Armatec-110 EpoCem, CLEANING OF EQUIPMENT will improve adhesion on large areas or where particu-larly dense concrete substrates are involved. Mfr #: 324324 From: $194.93 Add to Cart. Temps de surcouchage prolong pour les mortiers de . Apply subsequent repair mortars wet on wet. 673 stream Suitable in concrete repair as corrosion protection for reinforcement. DO NOT ADD WATER! <>stream To achieve good bond, SikaTop Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). Excelente adherencia al hormign y el acero. Contains EpoCem technology - improved bonding agent Extended open times for repair mortars Compatible with most Sika MonoTop repair mortars Apply 2nd layer when the first coat is hard to the fingernail (~23 hours at +20 C). % Acts as an effective barrier against penetration of water and chlorides. Documents. P.O.Box 126212 Dubai, United Arab Emirates, Tel. adhesive anchoring systems; adhesive general construction & tapes; all thread; anchor bolts & holddown; mechanical anchoring systems %PDF-1.7 SikaTop Armatec-110 EpoCem meets the requirement of EN 1504-7. Freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain until application of the repair mortar. Shake components A and B thoroughly before opening. To achieve good bond, SikaTop Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). L(67g |rYAwPBi"yW3aFwiY]=\YSOD@bR 19C`J 1 o6/ d"D3qkF38HI":SgU,i I''V9U,mqoHtxG11LQ! SikaTop Armatec-110 EpoCem is part of the Sika repair system complying with the relevant part of European Standard EN 1504 and comprising of: Maximum waiting time before application of repair mortar Sika repair mortars and non-fast setting concrete can be applied on SikaTop Armatec-110 EpoCem within a maximum time of: As reinforcement corrosion protection coating:~2 kg per m2 and application layer (~1 mm thick)In total min. P273 Avoid release to the environment. NKmw))U6'x[A6>v$ <> tions relating to the application and end-use of Sika products, are given in good faith based on Sika's cur-rent knowledge and experience of the products when SikaTop Armatec-110 EpoCem Author: Sika Egypt, 1st Industrial Zone (A), Section #10, Block 13035, El Obour City, Egypt, TEL: +202 44810580, FAX: +202 44810459, egy.sika.com Apply subsequent repair mortars wet on wet Freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain un-til application of the repair mortar. System structure SikaTop Armatec-110 EpoCem is part of the Sika repair system com-plying with the relevant part of European Standard EN 1504 and compris- . xSn@+8.;iT@"[%*(2$#=JAu)nJc~waCDxA_]/H'4C_UFL0453DF}3T!~Cip%&YH$#%Z$JYh#GZ0uc ` (h,%_C,}[~]pw|yTS1 u*S~4//(H9.kqDz>mn]LPW\ Read more + Contains EpoCem technology - improved bonding agent recommendations relating to the application and end-use of Sika products, are given in good faith based on Sika's current knowledge and experience of the products . . NEMO ETC, LLC ASTM C1289/TAS 110 4n-SIKA-19-SSINCB-01.B 09/05/19 MANUFACTURING LOCATION: 1. +62 21 . Sika re-ity of aggregates to be employed. Sika Corporation Sika Armatec 110 Application Instructions. Apply 2nd layer when the first coat is hard to the fingernail (~2 - 3 hours at +20C). Sika Armatec-10 ZR is a one-component, moisture-cured polyurethane primer modified with zinc, to provide protection against corrosion for reinforcing steel. Sikadur-32 LP or SikaTop Armatec-110 EpoCem, will improve adhesion on large areas or where particu- CLEANING OF EQUIPMENT larly dense concrete substrates are involved. SikaTop Armatec-110 EpoCem Author: PT. Apply subsequent repair mortars wet on dry (so not to wipe off the protection layer). SikaTop Armatec-110 EpoCem meets the requirement of EN 1504-7. To achieve good bond, SikaTop Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). +48 22 209 86 51 Godziny otwarcia Pon - Sob: 9:00 - 21:00 Sika Armatec-110 EpoCem March 2020, Version 01.02 020302020050000003 PRODUCT DATA SHEET Sika Armatec-110 EpoCem BONDING PRIMER AND REINFORCEMENT CORROSION PROTECTION . APPLICATION INFORMATION Fresh Mortar Density A+B+C ~125 lb/ft3 (~2.0 kg/l) Coverage Bonding agent 80 ft2/gal (7.4 m2/l) To achieve good bond, SikaTop Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). 110 F (-7 - 43 C). 2.Apply the bond coat of SikaTop Armatec-110 EpoCem at a thickness of not less than 0.5 to 1.0 mm (20 to 40 mil) using a stiff brush or a suitable spray gun (such as a Goldblatt unit). Brukowa 25, 05-092 omianki tel. SikaTop Armatec-110 EpoCem Author: SIKA IRELAND LIMITED, Ballymun Industrial Estate, Ballymun, Dublin 11, Ireland, Tel: +353 1 862 0709, Web: www.sika.ie, Twitter: @SikaIreland . SikaTop Armatec-110 EpoCem Author: Sika Portugal, SA, Rua de Santarm, 113, 4400-292 V. N. de Gaia, Tel. Kompatibiln s maltami ady Sika MonoTop. Tel : +91 22 62704038 Prodluuje dobu zpracovatelnosti opravnch malt. 48 0 obj tions relating to the application and end-use of Sika products, are given in good faith based on Sika's cur-rent knowledge and experience of the products when . 49 0 obj As a bonding primer: Apply using medium hard brush or spray gun to prepared substrate. Provides an excellent bonding coat for subsequent applications of repair mortars. Store properly in undamaged original sealed packaging, in dry cool conditions between +5 C and +25 C. CONTACT. SikaTop Armatec-110 EpoCem is a cementitious epoxy resin compensated 3-component coating material with corrosion inhibitor, used as bonding primer and reinforcement corrosion protection. System Structure SikaTop Armatec-110 EpoCem is part of the Sika repair system com-plying with the relevant part of European Standard EN 1504 and compris- . Weather Condensation with Insulation | BSCSika Armatec-110 EpoCem is a bonding primer and Full article: RASPA: molecular simulation software for Packaging and storage of orange juice | Orange Book Opening Diffusion Pathways through Site Disorder: The <> Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). Bewehrungskorrosionsschutz, Haftbrcke. Apply subsequent repair mortars wet on wet Freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain until application of the repair mortar. Refer to separate sheets for further information. tions relating to the application and end-use of Sika products, are given in good faith based on Sika's cur-rent knowledge and experience of the products when High mechanical strength. Hardened material can only be mechanically removed. Shiravane, Nerul, Navi Mumbai Contains corrosion inhibitor. Compare label. SikaTop Armatec-110 EpoCem Author: SIKA FRANCE S.A.S., 84 rue Edouard Vaillant, 93350 LE BOURGET, FRANCE, Tl. APPLICATION The application of a suitable bonding agent, such as Before pouring let the mixed grout stand for approx-Sikadur-32 LP or SikaTop Armatec-110 EpoCem, imately 5 minutes after mixing to allow entrapped air will improve adhesion on large areas or where particu- to escape. As reinforcement corrosion protection: Apply first layer approx. Protection anticorrosion et pont d'adhrence PCC 3 composants, enrichi de rsine poxy, conforme aux exigences de la norme EN 1504-7. Compare label. Galeria omianki ul. Sika Armatec-110 EpoCem is a cementitious epoxy resin compensated 3-component, solvent-free, coating material with corrosion inhibitor, used as bonding primer and reinforcement corrosion protection. Contains corrosion inhibitor. <>stream Contains corrosion inhibitor. Apply subsequent repair mortars wet on wet Freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain until application of the repair mortar. endobj 1 mm thick, using medium hard brush or spray gun to the cleaned reinforcement. 5 0 obj Apply one . Compatible con los morteros de reparacin Sika MonoTop . Sika Indonesia Head Office and Manufacturing, Jl. Longue dure de vie en pot. . adhesives & fasteners. tions relating to the application and end-use of Sika products, are given in good faith based on Sika's cur-rent knowledge and experience of the products when . Apply subsequent repair mortars wet on wet Freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain until application of the repair mortar. SikaTop Armatec-110 EpoCem. SikaTop Armatec-110 EpoCem is a cementitious epoxy resin compensated 3-component coating material with corrosion inhibitor, used as bonding primer and reinforcement corrosion protection. % . As reinforcement corrosion protection: Apply first layer approx. Compatible avec la plupart des mortiers de rparations SikaTop et Sika MonoTop. stream While still mixing components A and B slowly add powder component C. Mix the three components together for minimum 3 minutes, minimising addition of air. contact preventivo preventivo . Application under dynamic loading:SikaTop Armatec-110 EpoCem has been tested with the following Sika repair mortars and is certified for dynamic loading applications. SikaTop Armatec-110 EpoCem is a 3-component, water-based epoxy resin, anti-corrosion coating and bonding agent. 20 kg: A (1.14 kg) + B (2.86 kg) + C (16 kg), Portland cement, epoxy resin, selected aggregates and additives. As reinforcement corrosion protection:Apply first layer approximately 1 millimeter thick, using medium hard brush or spray gun to the cleaned reinforcement. Apply subsequent repair mortars wet on wet Freshly applied SikaTop Armatec-110 EpoCem must be protected against contamination and rain until application of the repair mortar. Horizontal . endobj CURING TREATMENT SikaTop Armatec-110 EpoCem vyhovuje poadavkm dle EN 1504-7. To achieve good bond, SikaTop Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). 533-279 Compatible with most Sika MonoTop repair mortars. Construction Sika Corporation Sika Armatec 110 EpoCem Bonding Agent and Reinforcement Protection Sika Armatec 110 EpoCem is a 3-component, solvent-free, epoxy- modified, cementitious product specifically formulated as a bonding System Structure SikaTop Armatec-110 EpoCem is part of the Sika repair system com-plying with the relevant part of European Standard EN 1504 and compris- . Protection anticorrosion des armatures, pont d'adhrence. To achieve good bond, SikaTop Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). xUMo@_17 of?mB4`\75vb{ZEl~M`HE>\wXE0[hUs=6ge mdtH2*MZU#1B:n|~)s-12C"2*e^h[\p-m|+[_bZS E! To achieve good bond, SikaTop Armatec-110 EpoCem must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). Contiene inhibidor de . Actual measured data may vary tions relating to the application and end-use of Sika due to circumstances beyond our control. Clean all tools and application equipment with water immediately after use. Compatible with most Sika MonoTop repair mortars. Hardened material can only be mechanically removed. : Expiration Date: 07/05/26 Approval Date: 10/13/22 . SikaTop Armatec-110 EpoCem can be mixed with a low speed (< 250 rpm) electric drill mixer.Shake components A and B thoroughly before opening. Contains EpoCem technology - improved bonding agent. Excellent adhesion to concrete and steel. Compare BASF MASTERPROTECT HB 400 . 0.5 - 1 mm thick, using medium hard brush or spray gun to the cleaned reinforcement. Greer, SC . . tions relating to the application and end-use of Sika products, are given in good faith based on Sika's cur-rent knowledge and experience of the products when . Created Date: 3/26/2021 12 .